JLG Boom Lift 450AJ HC3 Service & Maintenance Manual 3122564000 2026

[Hyundai]

Download this document, you need 2725 Gallons

JLG Boom Lift 450AJ HC3 Service & Maintenance Manual 3122564000 2026
Size: 110.86 MB
Format: PDF
Language: English
Brand: JLG
Type of Machine: Boom Lift
Type of Manual: Service & Maintenance Manual, Electrical and Hydraulic Diagrams
Model: JLG 450AJ HC3 Boom Lift
Part Number: 3122564000
Publication Date: 2026
Number of Pages: 944 Pages

Contents:
Safety

General​

1.1.1 Disclaimer​

1.1.2 Operation & Safety Manual​

Safety Information​

1.2.1 Safety Alert System and Signal Words​

Safety Hazards​

1.3.1 Personal Hazards​

1.3.2 Equipment Hazards​

1.3.3 General Hazards​

1.3.4 Operational Hazards​

Safety Decals​

Machine Verification​

General Machine Information and Specifications

Specifications​

2.1.1 Machine Specifications​

2.1.2 Machine Dimensional Data​

2.1.3 Engine Data​

2.1.4 Tires Specification​

2.1.5 Critical Stability Weights​

Serial Number Location​

Fluids and Lubrication​

2.3.1 General Information​

2.3.2 Hydraulic Oil​

2.3.3 Changing Hydraulic Oil​

2.3.4 Lubrication Specifications​

2.3.5 Fluids​

2.3.6 Capacities​

2.3.7 Lubrication Schedule​

Machine Characteristics​

2.4.1 Ground Control Keyswitch System​

2.4.2 Platform Control Enable System​

2.4.3 Cold Start System (DIESEL)​

2.4.4 Fuel Reserve / Cut-out System​

2.4.5 HRC Engine Emission Characteristics​

2.4.6 Diesel Particulate Filter (If Equipped)​

2.4.7 Drive System​

2.4.8 Drive Orientation System​

2.4.9 Function Speed Control System​

2.4.10 Oscillating Axle System​

2.4.11 Chassis Tilt Indicator System​

2.4.12 Platform Load Sensing System (LSS)​

2.4.13 ClearSkyTM System Ready​

2.4.14 Tires and Counterweight​

2.4.15 Side Entry Platform​

2.4.16 Transport Position Sensing System​

2.4.17 Beyond Transport Position - Drive Speed Cutback System​

2.4.18 Drive Steer - Boom Function Interlock System (CE Only)​

2.4.19 Ground Panel Display​

2.4.20 Jib Lift (if equipped) End of Stroke Dampening​

2.4.21 Main Boom Lift End of Stroke Dampening​

2.4.22 Emergency Decent System​

2.4.23 Diagnostics/Controller Programming​

2.4.24 Telescope Retracted Sensor​

2.4.25 Triple Capacity System​

2.4.26 Unrestricted capacity 660 lb (300 kg) - (Yellow)​

2.4.27 Restricted Capacity 750 lb (340 kg) - (Blue)​

2.4.28 Restricted Capacity 1000 lb (460 kg) - (Green)​

Clearsky Smart Fleet (If Equipped)​

2.5.1 General​

2.5.2 ClearSky Smart Fleet™ — Access Control​

Maintenance and Inspection Schedules

Machine Preparation, Inspection, and Maintenance​

3.1.1 General​

3.1.2 Preparation, Inspection, and Maintenance​

3.1.3 Pre-Start Inspection​

3.1.4 Pre-Delivery Inspection and Frequent Inspection​

3.1.5 Annual Machine Inspection​

3.1.6 Preventive Maintenance​

Service and Guidelines​

3.2.1 General​

3.2.2 Safety and Workmanship​

3.2.3 Cleanliness​

3.2.4 Components Removal and Installation​

3.2.5 Component Disassembly and Reassembly​

3.2.6 Pressure-Fit Parts​

3.2.7 Bearings​

3.2.8 Gaskets​

3.2.9 Bolt Usage and Torque Application​

3.2.10 Hydraulic Lines and Electrical Wiring​

3.2.11 Hydraulic System​

3.2.12 Lubrication​

3.2.13 Battery​

3.2.14 Welding on JLG Equipment​

Preventive Maintenance and Inspection Schedules​

3.3.1 Maintenance Schedules​

Pins and Composite Bearing Repair Guidelines​

Tires and Wheels​

3.5.1 Tire Replacement​

3.5.2 Tire Damage​

Fuel Tank Inspection​

Boom Inspection and Maintenance​

3.7.1 Boom Cleanliness Guidelines​

3.7.2 Boom Wear Pad Inspection​

Hydraulic Filter Replacement​

3.8.1 Hydraulic Filter Removal​

3.8.2 Hydraulic Filter Installation​

Turntable Bearing Inspection​

3.9.1 Turntable Bearing Mounting Bolt Condition Check​

3.9.2 Wear Tolerance​

Engine General Inspection​

3.10.1 General Maintenance​

3.10.2 Glow Plugs​

3.10.3 Checking Oil Level​

3.10.4 Replacing Engine Oil​

3.10.5 Replacing the Oil Filter​

3.10.6 Replacing the Primary Fuel Filters​

3.10.7 Replacing the Fuel Pre-Filter​

3.10.8 Replacing the Auxiliary Fuel Filter For Deutz D2011L03 T4I (Only)​

Bio Fuel In Deutz Engines​

3.11.1 General​

3.11.2 Bio Fuel​

3.11.3 Biological Contamination In Fuels​

Deutz EMR2​

Deutz EMR5​

Generator Inspection​

3.14.1 Maintenance Schedule​

3.14.2 Overload Protection​

3.14.3 Inspecting Brushes, Replacing Brushes and Cleaning Slip Rings​

3.14.4 Troubleshooting​

Testing, Calibrations and Special Procedures

Special Tools​

4.1.1 Multimeter Basics​

4.1.2 Threadlocking Compound​

4.1.3 Tools Catalog​

Testing Procedures​

4.2.1 Starter​

4.2.2 SkyGuard​

4.2.3 LSS Testing and Evaluation​

4.2.4 Troubleshooting​

Calibration Procedures​

4.3.1 JLG Analyzer​

4.3.2 Calibration Preparation​

4.3.3 Load Sensing System Calibration​

4.3.4 Tilt Sensor Calibration​

4.3.5 Boom Angle Calibration​

4.3.6 Calibrating Level Up CRKPT​

4.3.7 Calibrating Level Down Crackpoint​

4.3.8 Calibrating Platform Angle Sensor​

Special Procedures​

4.4.1 Fuel Tank Cleaning and Drying​

4.4.2 Cylinder Checking Procedure​

4.4.3 Cylinder Drift​

4.4.4 Hydraulic Circuits​

4.4.5 Hydraulic Pressure Settings and Adjustments​

4.4.6 Hydraulic Pressures​

4.4.7 Oscillating Axle Bleeding Procedure and Lockout Test​

4.4.8 Lubricating O-rings in the Hydraulic System​

4.4.9 Foot Switch Adjustment​

Wheel Drive Hub​

4.5.1 Roll and Leak Testing​

4.5.2 Tightening and Torquing Bolts​

System Software

Load Sensing System (LSS)​

5.1.1 Theory of Operation​

5.1.2 Load Sensing Gauge Removal/ Installation​

JLG Analyzer​

5.2.1 Introduction​

5.2.2 Machine Data Access​

5.2.3 Hand Held Analyzer​

5.2.4 Using the Analyzer​

5.2.5 Changing the Access Level of the Hand Held Analyzer​

5.2.6 Adjusting Parameters Using the Hand Held Analyzer​

5.2.7 Machine Setup​

5.2.8 Analyzer Flow Chart​

Analyzer Software Accessibility​

5.3.1 Access Level​

5.3.2 Machine Set-Up​

5.3.3 Personalities​

Function Test​

ClearSky (CS550) Configuration and Troubleshooting​

5.5.1 ClearSky Smart FleetTM CS550 Configuration​

5.5.2 Troubleshooting​

Fault Codes

Fault Codes Introduction​

Engine Diagnostic​

6.2.1 Deutz Trouble Codes (D2.9L4 Engine)​

6.2.2 Deutz D2.9L4 (Stage V) Engine​

6.2.3 Deutz D2.3 L3 Engine Trouble Codes​

6.2.4 Engine Fault Codes - Kubota Engine​

Machine Fault Codes​

6.3.1 General​

6.3.2 ClearSky Smart Fleet DTC Fault Codes​

ClearSky CS550 Troubleshooting Procedures​

Hydraulics

General Information and Safety​

Theories of Operation​

7.2.1 Cylinders​

7.2.2 Valves​

Hydraulic Components​

7.3.1 Hydraulic Oil Tank​

7.3.2 Drive Pump Pre-Fill Procedures​

7.3.3 Main Control Valve Pressure Setting​

Torque Values​

7.4.1 Cylinder Torque Specifications​

7.4.2 Valve Torque Specifications​

Hydraulics Installation​

7.5.1 Frame Hoses​

7.5.2 Turntable Hoses (US Built)​

7.5.3 Turntable Hoses (China Built)​

7.5.4 Boom Hoses​

Standard Hydraulic Diagram​

Electricals

General Information​

8.1.1 Applying Silicone Dielectric Compound to Electrical Connections​

8.1.2 Dielectric Grease Application​

Electrical Connectors​

8.2.1 Deutsch Connectors​

Board Layouts​

8.3.1 Ground Control Module Pin Connections​

8.3.2 Platform Control Module Pin Connections​

AMP Connector​

8.4.1 Assembly​

8.4.2 Disassembly​

8.4.3 Wedge Lock​

8.4.4 Service - Voltage Reading​

Wiring Harness and Connector Label Diagrams​

8.5.1 Connector Labels​

8.5.2 Component Labels​

Telematics Gateway​

8.6.1 Telematics-Ready (TCU) Plug​

Electrical Installation​

Removal and Installation

Wheel and Tire​

Chassis/Frame Assembly​

9.2.1 Axle and Drive Assemblies Troubleshooting​

9.2.2 Axle Assembly​

9.2.3 Drive Hub and Motor​

9.2.4 Spindle Assembly​

Boom​

9.3.1 Boom Components Terminology​

9.3.2 Main Boom Powertrack​

9.3.3 Boom Assembly​

9.3.4 Rotator Assembly​

9.3.5 Jib Assembly​

Platform​

9.4.1 Platform (Rapid Replaceable Platform)​

9.4.2 Platform Support (Traditional Design)​

9.4.3 Platform Support (Rapid Replaceable Platform)​

9.4.4 Bolt-on External Fall Arrest​

Engine​

9.5.1 Component Terminology​

9.5.2 Engine Serial Number​

9.5.3 Engine Replacement​

9.5.4 Surge Tank (Deutz D2.9 L4 Stage V/D2.9 L4 T4F/China IV)​

9.5.5 Surge Tank (Kubota Engine)​

9.5.6 Pump Coupling Kit​

9.5.7 Air Filter Assembly​

9.5.8 Radiator Assembly​

9.5.9 Thermostat​

9.5.10 Coolant Temperature Sensor​

9.5.11 Relay Assembly​

9.5.12 Starter​

9.5.13 Alternator​

9.5.14 Fuel Tank​

9.5.15 Pre- Fuel Filter and Fuel Pump — Deutz Engine​

9.5.16 Pre-Fuel Filter and Fuel Pump-Kubota Engine​

Transmission​

Hydraulic Cylinders​

9.7.1 Main Boom Lift Cylinder​

9.7.2 Platform Level Cylinder​

9.7.3 Steer Cylinder​

9.7.4 Jib Lift Cylinder​

9.7.5 Axle Lockout Cylinder​

Hydraulic Valves​

9.8.1 Boom Mounted Valves​

9.8.2 Main Control Valve​

9.8.3 Traction Control Valve​

Hydraulic Pumps​

9.9.1 Function Pump​

9.9.2 Drive Pump​

Electrical Components​

9.10.1 Battery​

Turntable​

9.11.1 Swing Bearing​

9.11.2 Swing Motor​

9.11.3 Counterweight​

Generator and Pulley​

9.12.1 For 7500W Generator - Deutz D2011L03​

9.12.2 For 4000W Generator - Deutz D2011L03​

9.12.3 For 2500W Generator - Deutz D2011L03​

9.12.4 For 2500W Generator - Kubota WG2503 and Deutz T4F​

9.12.5 For 7500W and 4000W Generator - Kubota, Deutz T4F and D2.9L4 Stage V​

ClearSky® LED Motion / Amber Beacon (CS550) (if equipped)​

9.13.1 ClearSky® LED Motion / Amber Beacon (CS550) (if equipped)​

Disassembly and Assembly

Drive Assembly​

10.1.1 Drive Hub​

10.1.2 Drive Brake​

Platform​

Boom and Jib Assembly​

10.3.1 Upper Boom​

10.3.2 Jib​

10.3.3 Rotary Actuator​

Engine Components​

10.4.1 Engine Disassembly, Inspection and Service​

10.4.2 Fuel Tank​

Pumps​

10.5.1 Function Pump​

10.5.2 Drive Pump​

Hydraulic Cylinders​

10.6.1 Axle Lockout Cylinder​

10.6.2 Platform Level Cylinder​

10.6.3 Jib Lift Cylinder​

10.6.4 Main Lift Cylinder​

10.6.5 Tower Boom Lift Cylinder​

10.6.6 Master Cylinder​

10.6.7 Steer Cylinder​

10.6.8 Telescope Cylinder​

Turntable​

10.7.1 Swing Motor​

10.7.2 Preparation Before Disassembly​

10.7.3 Disassembly and Inspection​

10.7.4 Assembly​

10.7.5 One Piece Stator Construction​

10.7.6 Two Piece Stator Construction​

10.7.7 Final Checks​

Generator Disassembly and Assembly​

Powertrack​

10.9.1 Remove Link​

10.9.2 Install New Link​

10.9.3 Replace Fixed End Brackets​

10.9.4 Replace Moving End Brackets​

Torque/Connection Information

Hydraulic Fittings​

11.1.1 Tapered Thread Types​

11.1.2 Straight Thread Types, Tube and Hose Connections​

11.1.3 Straight Thread Types, Port Connections​

11.1.4 Flange Connection Types​

11.1.5 Tightening Methods​

11.1.6 Assembly and Torque Specifications​

11.1.7 General Tube Type Fitting Assembly Instructions​

11.1.8 Assembly Instructions for American Standard Pipe Thread Tapered Connections.​

11.1.9 Assembly Instructions for British Standard Pipe Thread Tapered Connections​

11.1.10 Assembly Instructions for 37° (JIC) Flare Fittings​

11.1.11 Assembly Instructions for 45° SAE Flare Fittings​

11.1.12 Assembly Instructions for O-Ring Face Seal (ORFS) Fittings​

11.1.13 Assembly Instructions for DIN 24° Flare Bite Type Fittings (MBTL and MBTS)​

11.1.14 Assembly Instructions for Bulkhead (BH) Fittings​

11.1.15 Assembly Instructions for O-Ring Boss (ORB) Fittings​

11.1.16 Assembly Instructions for Adjustable Port End Metric Fittings​

11.1.17 Assembly Instructions for Metric ISO 6149 (MPP) Port Assembly Stud Ends​

11.1.18 Assembly instructions for Adjustable Port End (BSPP) Fittings​

11.1.19 Assembly Instructions for Flange Connections: (FL61 and FL62)​

11.1.20 Double Wrench Method​

11.1.21 FFWR and TFFT Methods​

11.1.22 Adjustable Stud End Assembly​

11.1.23 O-ring Installation (Replacement)​

Torque Charts​

11.2.1 SAE Fastener Torque Chart​

11.2.2 Metric Fastener Torque Chart​

Schematics

Hydraulic Schematics​

Electrical Schematics​

Deutz EMR2 Schematics​

12.3.1 Vehicle Side Connection Diagram​

12.3.2 Engine Side Connection Diagram - Sheet 1 of 2​

12.3.3 Engine Side Connection Diagram - Sheet 2 of 2​

12.3.4 Engine Plug Pin​

12.3.5 Vehicle Plug Pin Identification​

Deutz EMR5 Schematics​

12.4.1 Engine Plug Pin Identification​

12.4.2 Vehicle Plug Pin Identification​

4000W Generator Schematic​

12.5.1 Generator and Controller Circuit Diagram​

12.5.2 Lead Connection List​

7500W Generator Schematic​

12.6.1 Troubleshooting Circuit Diagram​

12.6.2 Generator and Controller Circuit Diagram​

12.6.3 Power Board PC1 Circuit Diagram​

12.6.4 Power Board PC2 Electrical Circuit Diagram​

12.6.5 Lead Connection List​