Hyundai Forklift 25LE-7U 30LE-7U 35LE-7U Operation Maintenance Manual

[Hyundai]

Download this document, you need 500 Gallons

Hyundai Forklift 25LE-7U 30LE-7U 35LE-7U Operation Maintenance Manual
Size: 9.73 MB
Format: PDF
Language: English
Brand: Hyundai
Type of Machine: Forklift
Type of Manual: Operation and Maintenance Manual
Model: Hyundai 25LE-7U 30LE-7U 35LE-7U Forklift
Number of Pages: 163 Pages

Contents:
SAFETY LABELS

1. LOCATION​

2. DESCRIPTION​

​

GUIDE

1.DIRECTION​

2.SERIAL NUMBER​

3. SYMBOLS​

​

1.SAFETY HINTS

1. DAILY INSPECTION​

2. DO'S AND DON'TS​

3. SEAT BELTS​

4. NO RIDERS​

5. PEDESTRIANS​

6. OPERATOR PROTECTION​

7. FORK SAFETY​

8. PINCH POINTS​

9. TRAVEL​

10. GRADES, RAMPS, SLOPES AND INCLINES​

11. TIP OVER​

12. SURFACE AND CAPACITY​

13. PARKING​

14. REFUELING​

15. STEP​

16. OPERATOR'S SAFETY RULES​

17. SIDE SHIFT​

​

2. OPERATING HAZARDS

1.LOOSE LOADS​

2. LONG AND WIDE LOADS​

3. REAR SWING​

4. LOW OVERHEAD CLEARANCE​

5. FAST TURNS AND HIGH LOADS​

6. DROP-OFFS​

7. RIGHT ANGLE STACKING​

8. CHAIN SLACK​

9. PALLETS AND SKIDS​

10. CAUTION FOR ELECTRICAL LINES​

11. LIFTING LOADS​

12. SIDE SHIFT​

13. FORK POSITIONER​

​

3.KNOW YOUR TRUCK

1. GENERAL LOCATIONS​

2. DATA/SAFETY PLATES AND DECALS​

3. INSTRUMENTS AND CONTROLS​

4. INDICATOR SYMBOLS​

5. OPERATING LEVER AND SWITCH​

​

4. OPERATOR MAINTENANCE AND CARE
1) DAILY SAFETY INSPECTION
2) FUEL SAFETY PRACTICES
5. STARTING AND OPERATING PROCEDURES

1. BEFORE OPERATING THE TRUCK​

2. CHECK BEFORE STARTING​

3. CHECK BEFORE STARTING ENGINE​

4. SEAT ADJUSTMENT​

5. STARTING FROM A SAFE CONDITION​

6. GENERAL STARTING AND OPERATING TIPS​

7. STARTING THE ENGINE​

8. CHECK AFTER STARTING ENGINE​

9. LEVERS AND PEDALS​

10. OPERATING SAFELY​

11. LOAD HANDLING​

12. SHUT DOWN PROCEDURE​

​

6.EMERGENCY STARTING AND TOWING

1. HOW TO TOW A DISABLED TRUCK​

2. HOW TO USE BATTERY JUMPER CABLES​

​

7. PLANNED MAINTENANCE AND LUBRICATION

1. INTRODUCTION​

2. SAFE MAINTENANCE PRACTICES​

3. INSTRUCTIONS BEFORE MAINTENANCE​

4. PLANNED MAINTENANCE INTERVALS​

5. MAINTENANCE CHART​

6. HOW TO PERFORM PLANNED MAINTENANCE​

7. REPLACEMENT​

8. LUBRICATION CHART​

9. GREASING POINT​

10. HANDLING MACHINE IN EXTREMELY HOT PLACES​

11. COLD WEATHER OPERATION​

12. STORAGE​

13. TRANSPORT​

14. LOADING AND UNLOADING BY CRANE​

15. RECOMMENDATION TABLE FOR LUBRICANTS​

16. FUEL AND LUBRICANTS​

​

8. MAINTENANCE ON REGULATOR
9. SPECIFICATIONS

1. SPECIFICATION TABLE​

2. SPECIFICATION FOR MAJOR COMPONENTS​

3. TIGHTENING TORQUE​

​

10. TROUBLESHOOTING

1. ENGINE SYSTEM​

2. ELECTRICAL SYSTEM​

3. TORQUE FLOW SYSTEM​

4. STEERING SYSTEM​

5. BRAKE SYSTEM​

6. HYDRAULIC SYSTEM​

​

11. TESTING AND ADJUSTING

1. ENGINE SYSTEM​

2. DRIVE SYSTEM​

3. TRAVEL SYSTEM​

4. STEERING SYSTEM​

​