Hyundai Forklift 15D-7E to 80D-7E Operators Manual

[Martin Welker]

Download this document, you need 500 Gallons

Hyundai Forklift 15D-7E to 80D-7E Operators Manual
Size: 16.05 MB
Format: PDF
Language: English
Brand: Hyundai
Type of Machine: Forklift
Type of Manual: Operators Manual
Model: Hyundai Forklift
15D-7E 18D-7E 20DA-7E
20D-7E 25D-7E 30D-7E 33D-7E
20DF-7 25DF-7 30DF-7 33DF-7
35DF-7
35D-7AE 40D-7AE 45D-7E, 50D-7AE
35DS-7E 40DS-7E 45DS-7E 50DA-7E
50D-7E 60D-7E 70D-7E
50DF-7 60DF-7 70DF-7
50DS-7E 60DS-7E 70DS-7E
80D-7E
Number of Pages: 251 Pages

Contents:
FOREWORD
EC Declaration of conformity - update 05 01 ’10
A MESSAGE TO HYUNDAI LIFT TRUCK OPERATORS
INTRODUCTION
HOW TO USE THIS MANUAL
EC REGULATION APPROVED
SAFETY LABELS
GUIDE
SAFETY HINTS
1. DAILY INSPECTION
2. DO'S AND DON'TS
3. SEAT BELTS
4. NO RIDERS
5. PEDESTRIANS
6. OPERATOR PROTECTION
7. FORK SAFETY
8. PINCH POINTS
9. TRAVEL
10. GRADES, RAMPS, SLOPES AND INCLINES
11. TIP OVER
12. SURFACE AND CAPACITY
13. PARKING
14. REFUELING
15. STEP
16. OPERATOR'S SAFETY RULES
OPERATING HAZARDS
1. LOOSE LOADS
2. LONG AND WIDE LOADS
3. REAR SWING
4. LOW OVERHEAD CLEARANCE
5. FAST TURNS AND HIGH LOADS
6. DROP-OFFS
7. RIGHT ANGLE STACKING
8. CHAIN SLACK
9. PALLETS AND SKIDS
10. CAUTION FOR ELECTRICAL LINES
11. LIFTING LOADS
12. SIDE SHIFT
13. FORK POSITIONER
KNOW YOUR TRUCK
1. GENERAL LOCATIONS
2. DATA SAFETY PLATES AND DECALS
3. INSTRUMENTS AND CONTROLS
4. INDICATOR SYMBOLS
5. OPERATING LEVER AND SWITCH
6. OTHERS
OPERATOR MAINTENANCE AND CA
1. DAILY SAFETY INSPECTION
2. FUEL SAFETY PRACTICES
STARTING AND OPERATING PROCEDURES
1. BEFORE OPERATING THE TRUCK
2. CHECK BEFORE STARTING
3. CHECK BEFORE STARTING ENGINE
4. SEAT ADJUSTMENT
5. STARTING FROM A SAFE CONDITION
6. GENERAL STARTING AND OPERATING TIPS
7. STARTING THE ENGINE
8. CHECK AFTER STARTING ENGINE
9. LEVERS AND PEDALS
10. OPERATING SAFELY
11. LOAD HANDLING
12. SHUT DOWN PROCEDURE
EMERGENCY STARTING AND TOWING
1. HOW TO TOW A DISABLED TRUCK
2. HOW TO USE BATTERY JUMPER CABLES
PLANNED MAINTENANCE AND LUBRIC
1. INTRODUCTION
2. SAFE MAINTENANCE PRACTICES
3. INSTRUCTIONS BEFORE MAINTENANCE
4. PLANNED MAINTENANCE INTERVALS
5. MAINTENANCE CHART
6. HOW TO PERFORM PLANNED MAINTENANCE
7. REPLACEMENT AND CHECK
8. LUBRICATION CHART
9. GREASING POINT
10. HANDLING MACHINE IN EXTREMELY HOT PLACES
11. COLD WEATHER OPERATION
12. STORAGE
13. TRANSPORT
14. LOADING AND UNLOADING BY CRANE
15. RECOMMENDATION TABLE FOR LUBRICANTS
16. FUEL AND LUBRICANTS
SPECIFICATIONS
1. SPECIFICATION TABLE
2. SPECIFICATION FOR MAJOR COMPONENTS
3. TIGHTENING TORQUE
TROUBLESHOOTING
1. ENGINE SYSTEM
2. ELECTRICAL SYSTEM
3. TORQUE FLOW SYSTEM
4. STEERING SYSTEM
5. BRAKE SYSTEM
6. HYDRAULIC SYSTEM
TESTING AND ADJUSTING
1. ENGINE SYSTEM
2. DRIVE SYSTEM
3. TRAVEL SYSTEM
4. STEERING SYSTEM
5. ADJUSTMENT OF PARKING BRAKE LEVER